• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Fiat 500 Replacement Key Fob

It may be time to replace the battery if your 500 remote key fob is not working. If you replace the battery and it doesn't work, the problem may be somewhere else.

At United Locksmith, we specialize in making new keys for classic automobiles. We have all of the tools and components needed for this service.

Dead Coin Battery

The most frequent reason why your fiat punto key programming 500 key fob will not unlock or lock the doors is due to a dead battery. The battery of the coin cell inside the key fob will drain quickly if you don't use it frequently enough. If your remote began to show signs of weakness like a loss of range, and then stopped working completely the battery could be dead.

Metal clips keep the battery in inside the key fob. If the clips aren't tight, they can create contact problems that will prevent your remote from receiving power. Make use of a flathead screwdriver to open the retaining clips and remove the old battery. Be sure to choose a Replacement key fiat 500 with the same type of voltage, dimensions, and specification as the original battery.

The exposure to water can cause the key fob to corrode, or even become damaged. Even a brief bath in soapy water could cause damage to the electronic chip inside. Make sure your key fob is dry.

Water Damage

If your key fob isn't working properly, it could be caused by water damage. The rubber seals on key fobs keep them from being damaged by a small splash or drizzle of water. However, it's crucial to keep your keys of your car away from the ocean, washing machine, and even the pool.

The key cover fiat 500 fob contains an electronic chip that sends a signal to your car's immobilizer system. This is what allows your 500 to lock or start, but if the chip gets saturated, it won't be able to longer function.

If you're looking to determine if your key fob is still functioning you can clean the internal electronics with isopropyl or electronic cleaner. However, it's best to get a replacement from a dealership rather than trying to repair an item that has been submerged by salt water.

A replacement fob can cost you a little bit but it's far cheaper than having to have your Fiat 500 towed to a dealership and fixed there! You can also do it yourself by following a few simple steps. Make sure you have the correct type of battery before you attempt to open your key fob. This is a job that's much simpler than it appears, and you can find step-bystep instructions online for almost any car key fob.

Faulty Chip

The chip located within the key fob communicates with your car's immobiliser unit to ensure the car is capable of starting when the correct key is inserted. If the chip is damaged or destroyed the car won't start no matter what you do.

Water damage or a dead cell battery are the most frequently cited reasons for a faulty chip. It is best to hand over the work to a professional locksmith who can replace the chip in a short time and at a an affordable price.

If your key fob fails to function after exposure to clean water from the tap or rain, take off the battery and clean the electronic component using a paper towel to ensure it is fully dry before putting it back in. If the key fob isn't working it's probably to be a damaged chip and must be replaced.

A few people turn to their dealer when they are in need of a new Fiat key fob, but this can be a very costly alternative. If you're seeking a cost-effective solution to get your Fiat key fob repaired Look no further than United Locksmith. We have the tools and experience needed to repair your Fiat fob in a timely and professional way.

Faulty Receiver Module

Fiat key fobs send a signal to the vehicle which will unlock and close doors (and start the vehicle for those with an automatic transmission) up to 50 feet. However, there are a few factors that could cause the fob to stop functioning. This could be due to a dead coin battery damaged by water buttons, worn ones, a receiver module issue or signal interference, or a malfunctioning electronic chip.

If the fob was placed in a pocket which has suffered severe trauma (such as being dropped on a hard floor or being washed in the washer) it might not be able to connect with the Body Control Module (BCM) of the vehicle. This is because the BCM is a secure system that can only accept signals from a genuine original key and not another.

It is necessary to replace the fob in case this occurs. A professional locksmith will manage the entire replacement process including programming a brand new key for your 500. In fact, they can provide you with a clone key that functions exactly the same as the original fob (and costs only a fraction of the price).