• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

how to replace a lock on a upvc door to Replace Door Locks

Your first protection is your door lock. It will prevent unauthorized entry to your home. The signs of wear and tear as well as instances like moving into a new house or break-ins, can necessitate the need to replace your lock.

You can determine the size of your cylinder by measuring the distance from the center of the knoblock cylinder to the adjustment screw. This measurement will allow you to purchase the appropriate lock.

Deadbolt

If you're looking to ensure that your door is secure against intruders, it's a good idea to install a deadbolt. The bolt extends into the strike plate on the doorframe when it is locked, making it much more difficult for a burglar to gain entry through the door. A single cylinder deadbolt is activated using an exterior key on the side and a thumb turn part on the interior. Deadbolts are only effective when it's properly installed, though.

First, you must find out if the door has an existing hole for a deadbolt, or if you need to drill it. Mark the position of the hole for the deadbolt on the surface of the door using the template that came with your lock installation set. Then, you can use your tape measure to determine the height the deadbolt needs to be. Then, mark the height on the side of the door. You can then use the speed square to draw an even line across the mark you made for the bolt hole.

Then using an electric drill, bore out the hole until it is on the opposite side of the door. This could take a bit of time. Sand the hole and edge of the door to smooth it. At this stage, it's a great idea also to paint or stain your door.

Remove any visible screws from the deadbolt. This will reveal the back and front assemblies of the deadbolt as well as the bolt inside. Then unscrew the old bolt and replace door lock it by an alternative bolt that matches the door hardware. It is necessary to remove the bolt from a setplate. Then, you'll need to chisel the area on the door frame for the strike plate.

If your strike plate is not aligned it's likely that the previous installer didn't correctly mortise it or a weatherstripping was installed and changed the strike's position. It is necessary to re-mortise the strikeplate and perhaps even the deadbolt to fix the issue. After this is done, test the deadbolt by closing and locking it. Test the deadbolt by closing and locking it after the bolt has been extended into the strike plate.

Knob

It could make your business and home less secure If the knob on your door is worn. It could also make opening or closing the door more difficult, which is why it is an ideal idea to replace the knob. Replacing the knob is an easy DIY task that should not take longer than 30 minutes to complete. You can use a screwdriver as well as pliers to get rid of the knob or handle, but be careful not to damage any other parts on the door.

Before you begin you'll need to spray WD-40 or a different dry lubricant onto the mechanism of the patio door lock replacement knob. This will help the new lock slide effortlessly as you turn it. It's important to use the best knob and replace Door lock handle that is compatible with the doors you currently have to ensure proper operation. If you don't have a match, you'll need to buy a replacement doorknob and latch plate.

Before you begin the replacement, look over the knob you replaced to determine which screws are holding it in place. If there aren't any screws you can use a screwdriver to insert between the cover plate and the plate with hidden screws and then remove it.

After you have removed the knob, inspect it for indications of damage and rust. You'll need to clean it off if you notice any scratches or dents, but you shouldn't have to do anything If the knob is in good shape.

Install the new knob. You should first examine the two knobs in order to make sure that you are choosing the correct one for your door. You'll need to pick one with an extending rod that locks with the rod mechanism of the second knob. Once you've put the new knob in the hole in the door and then carefully place it in the latch.

Thread the latch plate screws down and test the spring by pressing down on it several times. The latch should pop up each time. Next, install the other new knob and interlock it with the rod mechanism of the first knob. Thread the long screws of the doorknob's interior through the cylinder holes on the outside knob and fix it in its place.

Latch

A latch is a piece of metal that extends through the doorjamb to secure it closed. It is operated by a knob or handle on the inside of the door, or a thumb turn on the outside side of the door. A deadbolt can be used to secure a latch and stop intruders from breaking through the glass of the door. It can also guard against the accidental or deliberate closing by pets or children. It is possible to install an entry point with either a single-cylinder or double-cylinder deadbolt depending on your preferred level of security.

Installing a deadbolt is exactly the same as installing a latch however there are some differences. First, determine the setback of the doorjamb using an instrument to make sure the new lock will fit. The setback is the distance between the edge of the doorjamb to the middle of the hole for the latch faceplate. The standard setback is 2 3/8 to 2 3/4 inches. If you have a higher setback, you may have to purchase a longer latch from a hardware shop or locksmith.

The next step is to drill an edge bore hole into the doorjamb for the latch plate. Utilize a chisel to chisel the latch mortise. Make sure the hole's depth is enough to allow the faceplate to be flush with the doorjamb. Place the strikeplate on the floor to ensure it's placed correctly.

If the strike is set too high, the door could be pushed in or pressure put on it using a crowbar, or tire iron. This can also cause the doorjamb's to crack. To correct this, the strike can be lowered by drilling another hole in the doorjamb and chiseling out the center of the previous hole.

The last step is to install the new strike plate, which can be accomplished by screwing it in place over the screw holes that are already in place. Use wood putty afterwards to fill in any existing bolt holes or screw holes which aren't going to be used. After the putty is dry, sand it to an even finish.

Strike

An electric strike is a metal part where the latch and deadbolt engage when the door is shut. It is an essential component of the lock's overall security because it prevents the door from opening and provides an additional barrier to force or kicking. If a door is fitted with an electronic strike, it will be opened only by an entry key and a control unit that regulates the electrical impulses.

In the past, putting in an electronic strike was as simple as cutting off a part of a doorjamb to release the latchbolt of a cylindrical lock from the pocket inside the strike. This modification is not just ugly, but also exposes the latchbolt mechanism and the keeper to intruders.

Recently, a variety of electric strike manufacturers have come up with a "No Cut" type of strike that doesn't require a cutout to operate. These strikes have a unique design that allows the keeper and latchbolt to slide into the strike pocket without marring the doorjamb faceplate.

The strike is equipped with an internal ramp that lifts the latchbolt and keeper when it receives an electrical impulse from a controller or reader. The retracting of the keeper and latchbolt pushes them up higher on the ramp, which locks the door. When the door is closed the deadbolt remains in retracted and the latchbolt retracts into the keeper.

Installing an electric strike can be an easy process, particularly when you are replacing the strike on a previous patio door locks replacement. If you're planning to upgrade an existing access control system to an electric strike, you need to ensure that the new system is compatible. It is also necessary to make sure that the strike is properly connected to your access-control system and is set up to operate in a fail-safe way.

One way to safeguard against access by unauthorized persons is to upgrade the strike on your doors to a robust strike plate. These plates can be fitted with up to six screws of three inches instead of two screws of three-fourths inch. The longer screws make it harder for someone to break the frame and then reach inside to turn the thumb turn part of a single deadbolt cylinder.