• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Fix a Loose Door Hinge

Repairing a broken door hinge is a simple task for most homeowners. But, if the holes for screws are smashed and can't hold screws, you might have to use wood glue and dowels before you can install the hinge.

Before you do this, however you should clean off any surface rust. This will allow the dowels to stay in place and give them a solid base to hold onto.

Take off the Hinges

Many hinges for doors can be removed, which makes it easier to move a door from one side of the frame to the other or take the entire door off when needed. Anyone with a little patience can remove the hinges, but you must be aware of what to do.

If the hinges have been painted you'll need to take off the paint before you attempt to remove the pins. If you do not, the paint may be smashed off and scratch your door when you attempt to lift it. Place the hinges in a stainless steel pot and fill it up with water to the point that the hinges are completely submerged. Let the hinges sit in the pan for approximately 30 minutes. The heat of the water will soften the paint, making it easier to remove.

After the pins have been removed, take the hinges and the frame from the door. You can employ a screwdriver for the job done, however it is recommended to make use of a magnetic screwdriver for this project. This type of screwdriver was designed to grab screws made of metal and can make the work go much faster.

Before you attempt to remove the hinges, it is a good idea to spray them with some oil. A simple lubricant can help you speed up the process and make the removal of pins and screws more easily. This kind of lubricant can be found at most hardware stores as well as home improvement shops.

The number of hinges needed will also depend on what type of door you have, and how it's set up. Heavier doors and solid-core doors will need more hinges, while lighter-weight and hollow-core doors might require just two or three hinges.

Understanding the different types of hinges will help determine which one is best for your needs. The hinges on the exterior are designed to support the door's weight however, interior hinges will have to be able to support lighter loads.

Reattaching the replacement upvc hinges

Sometimes a door hinge will become looser over time and begin to hang out of alignment or slide. This could be a problem, but it's usually easy to solve. A simple tightening can resolve the issue. If the screw holes have been ripped out, it may be difficult to fix door hinge. A dowel made of wood can be used to tighten these holes once more.

Begin by drilling the hole using a drill close to the size of the new screw (normally 3/8"). Fill in the hole using wood glue and a wooden stick. To ensure a secure fit, the dowel must be cut to the same length as the screw. Then, you can reinstall the screw and tighten it until the desired degree of tightness. If the door has a tendency to bind, then add another dowel to the gap and repeat the procedure. Be sure to close the door slowly in order to check the perimeter clearances after each adjustment.

You can also use a wooden plug in place of the dowel. This is also a viable option however it may take some time to put in. Simply whittle a chunk of wood to the right size for a snug fit, then tap it into the hole. If you don't own an instrument for woodworking, you can use toothpicks or matchsticks made of wood.

After you've reinstalled your new screw and countersink the screw, you can use a countersink tool to make the hole for the screw's head smaller so that it does not rub against the edge of the door when it is opened and closed. This will make it easier to tighten the screw when reinstalling the hinge.

After you have reinstalled the hinge, make sure to coat it using a dry lubricant to help keep it from getting stuck in the future. You can use products such as PB Blaster and Liquid Wrench. You should apply a light coat and wait for approximately 15 minutes to reach the barrel of the hinge.

Refinishing the Hinges

If you are not ready to replace the hinges on your door, you can make a few repairs. Verify that the screws that secure the hinge plate to both the door frame as well as the frame are in good condition. If they're loose, tighten them with an electric drill or screwdriver. Be careful not to tighten the screws to the point that they start to create gaps in the trim joints, or even worse cause threads to be stripped.

If you're experiencing issues because the hinge plates are separated from the door and jamb, you can reattach them by applying wood glue to the back of the plates, and then inserting wooden dowels or toothpicks into the holes. Dowels and toothpicks provide a solid base for the screws, which will stop the plates from shifting when you drive them in. Let the glue dry before attaching the double glazing hinge repairs.

Another reason that causes hinges that are loose is that screws are worn out or are missing. This issue can be resolved by replacing the screws. Make sure the drill bit is similar to the size of the screw hole to avoid drilling into the hinge or jamb.

Close the door after you've reattached your upvc window hinge repair and check the gap between the frame and the door. The gap should be about the thickness of a penny or less if the old door was not hung correctly. If the hinges were put in place correctly, this should not be an issue.

If you notice that the hinges are still loose, try putting the thicker shim of the hinge between the hinge plate and the mounting surface to give an extra inch of space. You can also try removing the hinge pin from the problem hinge and pounding it down with a hammer to make it tighter or use a new hinge pin altogether. You can also grease your hinges with mineral oil or jojoba to reduce friction and keep them in their place. Regularly lubricating your hinges will aid in keeping them from becoming stiff or squeaky, and can also extend their life.

Cleaning the Hinges

The continuous movement of hinges causes friction, which attracts dust particles. These particles can become stuck and build up in the moving parts of door hinges, if they're not cleaned and lubricated regularly. The hinge will get stiff and creaky and its appearance may rapidly deteriorate. Regular cleaning, lubrication and inspections will maintain the integrity and functionality of hinges that are attached to doors.

Check the hinges to see how much rust has accumulated on their surface. If the rust has corroded to the point of destroying surface of the hinge barrel or screw holes, you will have to replace the hinges. If you are able to save the hinges, you should first clean off loose rust using steel wool and a wire brush. Apply a commercial rust-removing product or homemade solutions like lemon juice to the hinge. Allow the rust-removing solution to remain on the hinges for a few minutes in order to penetrate and dissolve any remaining rust.

Retightening screws can restore hinge functionality in the event that you don't want to spend time or money on repairing hinges. If you have stripped the screws however, it might be necessary to attach the dowel of wood or shim to the hinge. Dowels made of wood come in round rods of varying lengths and sizes. They can be purchased online, in stores selling woodworking supplies and home improvement stores.

A shim can also be made from metal or plastic, depending on the kind of hinge you have. To make a dowel, you need to cut a wooden dowel to the desired length. You can dip the dowel into the adhesive of a carpenter and then insert it into the hole. The glue will hold the dowel securely in place.

Before you start cleaning the hinges, place down a towel or a paper towel to shield floors and other surfaces from drips and spills that could happen. After securing the area, clean the window hinges replacement using an easy sponge or cloth coated with mild cleaner to eliminate dirt and grime. Also, tarnish and rust can be removed. You can make use of a small or toothbrush brush to get into difficult-to-reach areas in tight spaces and crevices.